Viessmann VITOCAL 222-G Datenblatt Seite 60
- Seite / 236
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1. Remove the front part of the ther-
mal insulation.
2. Remove the top part of the thermal
insulation.
3. Insert the strain relief with inserted
cables (lying at the bottom of the
thermal insulation) into the groove
of the recess in the lower part of
the thermal insulation.
4. Check the floor area, valves and all
visible solder joints of the heat
pump for traces of oil.
Note
Traces of oil indicate a leaking
refrigerant circuit. Ask a refrigera-
tion engineer to check the heat
pump.
Heat pump preparation (cont.)
60
Installation sequence
5592 969 GB
- VIESMANN 1
- Safety instructions 2
- Safety instructions (cont.) 3
- Installation instructions 4
- Service instructions 4
- Index (cont.) 5
- Positioning 9
- Transport 9
- Positioning (cont.) 10
- Heating circuit 14
- Natural cooling function 15
- Hydraulic diagram 18
- Electrical connection 18
- Equipment required 18
- System version 1 19
- System version 1 (cont.) 20
- System version 2 27
- System version 2 (cont.) 28
- System version 3 36
- System version 3 (cont.) 37
- System version 4 45
- System version 4 (cont.) 46
- Preparing the installation 56
- Heat pump preparation 59
- Heat pump preparation (cont.) 60
- Installing the control module 61
- Inserting the heat pump 62
- Inserting the cables 64
- Inserting the cables (cont.) 65
- Sensor connections 66
- Central fault message 69
- DHW circulation pump 70
- Power supply 74
- Power supply (cont.) 75
- position (like the 89
- Connecting the DHW 94
- Connection panel 94
- Connecting the DHW (cont.) 95
- Connecting the brine side 98
- 5592 969 GB 100
- Removing the front panels 101
- Maintaining service reports 101
- Vitocal 242) 105
- System configuration 109
- Checking the secondary pump 113
- Checking the primary pump 115
- Programming unit overview 123
- Fault messages 123
- Control unit diagnostics 123
- Acknowledging fault messages 124
- Scanning fault messages 124
- Skipping fault messages 125
- Displaying fault messages 125
- Diagnosis 130
- Diagnosis (cont.) 131
- Main menu > Information 134
- A see page 136 B see page 137 135
- C only for the Vitocal 242 135
- Control settings 135
- A see page 135 B see page 137 136
- A see page 138 B see page 140 141
- Adjusting sensor temperatures 143
- Checking signal inputs 144
- "Relay" sub-menu 145
- "Mixer" sub-menu 145
- Power-OFF contact: 1S 147
- System design 147
- Frost protection temperature 149
- Maximum flow temperature 150
- Minimum return temperature 150
- Power-OFF compressor 150
- Min. compressor off 152
- Flow; primary/secondary pump 152
- Minimum runtime 152
- Optimum runtime 153
- Optimum runtime (cont.) 154
- Electric heating 155
- E heating 155
- DHW with electric power 156
- Electric heating (cont.) 156
- Electric heating threshold 157
- Heater rod delay 157
- Time for drying buildings 159
- Internal pump run-on 160
- Max. steps; three-way valve 160
- Flow hysteresis 160
- Maximum temperature 162
- Solar collector 162
- Pump kick hysteresis 163
- Pump kick runtime 164
- Pump kick hysteresis (cont.) 164
- Pump kick dead time 165
- Flow rate 165
- Pump kick runtime (cont.) 165
- DHW program temperature 166
- DHW circulation pump program 166
- Operating mode 166
- DHW cylinder temperature 166
- DHW cylinder maximum 167
- Stop optimisation 169
- DHW auxiliary function 169
- Set DHW temperature 2 169
- Heat pump cylinder volume 169
- Start optimisation 169
- Maximum DHW runtime 170
- Maximum DHW interruption 170
- Excess reaction 170
- Reduced temperature 172
- Remote control 172
- Standard temperature 172
- Minimum flow temperature 173
- Operating mode (cont.) 173
- DHW during party mode 174
- Room temperature sensor 175
- Excess reaction (cont.) 175
- Room temperature hook-up 176
- Room temperature control 177
- Flow T excess 178
- Mixer parameters 179
- Mixer runtime 179
- Screed function 180
- Mixer active zone/dead zone 181
- Screed function (cont.) 181
- V Flow temperature 182
- Vs Set flow temperature 182
- Vh Active zone 182
- Vt Dead zone 182
- Cooling curve level/slope 183
- Natural cooling with mixer 184
- Cooling mixer runtime 185
- Cooling mixer parameters 186
- Buffer cylinder program 187
- Fixed temperature 187
- Buffer cylinder 187
- Hysteresis temperature 188
- Fixed temperature (cont.) 188
- Maximum temperature (cont.) 189
- Sensor resistance curves 191
- Main connection area 194
- Main connection area (cont.) 195
- Safety chain, 400 V units 196
- Safety chain, 230 V units 197
- Left part of the main PCB 198
- R.h. part of the main PCB 202
- Parts list Vitocal 242-G 204
- Parts lists 206
- Parts list Vitocal 222-G 210
- Hydraulic parameter report 216
- Control parameter report 217
- Switching times 219
- Z characteristic required 223
- L and DHW heating 225
- Declaration of conformity 230
- Keyword index 232
- Keyword index (cont.) 233
- Applicability 236
Verwandte Produkte und Handbücher für Wärmepumpen Viessmann VITOCAL 222-G
(10 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.510 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern